Kbogacik at 18:20, 26 January 2021

2021-01-26T18:20:21Z

← Older revision		Revision as of 13:20, 26 January 2021
Line 9:		Line 9:
	'''Procedure Number'''		'''Procedure Number'''

	MT 110-09, Rev. 0		MT 110-09, Rev. 1
	\|width="33%"\|		\|width="33%"\|
	'''Date'''		'''Date'''

	~~DRAFT~~		1/26/2021
	\|}		\|}

Kbogacik: /* General */

2021-01-26T18:18:46Z

General

← Older revision		Revision as of 13:18, 26 January 2021
Line 17:		Line 17:

	= General =		= General =
			[[File:DeWalt Scroll Saw.png]]

	= Reference =		= Reference =

Kbogacik: /* Specifications */

2021-01-26T18:17:22Z

Specifications

← Older revision		Revision as of 13:17, 26 January 2021
Line 47:		Line 47:
	TBD		TBD

	'''~~THIS IS THE~~ END OF THE PROCEDURE'''		'''END OF THE PROCEDURE'''

Aspontarelli: Created page with "{| |width="33%"| '''Shop Area:''' Woodshop '''Tool:''' DeWalt 20" Scroll Saw '''Requires in-person training:''' Yes |width="33%"| '''Procedure Number''' MT 110-09,..."

2020-12-31T11:22:41Z

Created page with "{| |width="33%"| '''Shop Area:''' Woodshop '''Tool:''' DeWalt 20" Scroll Saw '''Requires in-person training:''' Yes |width="33%"| '''Procedure Number''' MT 110-09,..."

New page

{|
|width="33%"|
'''Shop Area:''' Woodshop

'''Tool:''' DeWalt 20" Scroll Saw

'''Requires in-person training:''' Yes
|width="33%"|
'''Procedure Number'''

MT 110-09, Rev. 0
|width="33%"|
'''Date'''

DRAFT
|}

= General =

= Reference =

* https://images.homedepot-static.com/catalog/pdfImages/9d/9d09c7f4-2e33-4cc8-a69e-d16f3f36c8e9.pdf

= Maintenance =

'''BRUSHES'''

* Inspect carbon brushes regularly by unplugging tool, removing the brush inspection cap and withdrawing the brush assembly.
* Keep brushes clean and sliding freely in their guides.
* Always replace a used brush in the same orientation in the holder as it was prior to its removal. If the brush is worn down to 3/8", it must be replaced.
* The tool should be allowed to “run in” (run at no load) for 10 minutes before use to seat new brushes.

'''Installing the Blade'''

* BEFORE INSTALLING A BLADE, UNPLUG THE SCROLL SAW.
* The blade is held in place by the thumbscrew blade clamps attached to the top and bottom arms of the scroll saw.
* Before installing a blade, make sure the blade tension lever is moved fully to the right.
* Loosen, but do not unscrew, the top and bottom thumbscrews.
* Thread the blade through the hole in table, with the teeth facing toward the front of the saw.
* Scroll saws cut on the down-stroke, so it is essential that teeth face forward and down.
* Insert the blade into the bottom blade clamp and securely tighten the thumbscrew.
* Next, insert the top of the blade into the top blade clamp and securely tighten the top thumbscrew.
* Properly adjust the tension of the blade before operating your scroll saw.

= Specifications =

TBD

'''THIS IS THE END OF THE PROCEDURE'''

Scroll saw maintenance and specifications - Revision history

Kbogacik at 18:20, 26 January 2021

Kbogacik: /* General */

Kbogacik: /* Specifications */

Aspontarelli: Created page with "{| |width="33%"| '''Shop Area:''' Woodshop '''Tool:''' DeWalt 20" Scroll Saw '''Requires in-person training:''' Yes |width="33%"| '''Procedure Number''' MT 110-09,..."